Differences

This shows you the differences between two versions of the page.

--- wiki:20_rdc_charger:35_commissioning:06_ev_fleet [2023/03/31 10:07] – ↷ Links adapted because of a move operation saso.santelj
+++ wiki:20_rdc_charger:35_commissioning:06_ev_fleet [2023/05/26 13:04] (current) – external edit 127.0.0.1
@@ Line 11: / Line 11: @@
 === Procedure to set RDX Charger as slave is as follows: ===
-  * [[wiki:20_rdc_charger:06_software:start#evse_overview|RDX Charger]] -> set Max current (1)
+  * [[wiki:20_rdc_charger:30_software:start#evse_overview|RDX Charger]] -> set Max current (1)
   * RDX Charger -> enable "EVSE works as slave" (2) Master SN presents serial number of master charger, it will appear once connection is established.
   * RDX Charger -> set current if connection with master is lost (3)
-  * [[wiki:20_rdc_charger:06_software:start#hems_configurator|HEMS Configurator]] -> settings -> set static IP (it's recommended) (4)
+  * [[wiki:20_rdc_charger:30_software:start#hems_configurator|HEMS Configurator]] -> settings -> set static IP (it's recommended) (4)
   * HEMS Configurator -> limiter -> set "No limiter" for RDX Charger (5)
-{{wiki:rdx_charger:hems_config_cluster_01.png?direct&800|}}
+{{wiki:20_rdc_charger:hems_config_cluster_01.png?direct&800|}}
 === Procedure to set RDX Charger as master is as follows: ===
-  * [[wiki:20_rdc_charger:06_software:start#hems_configurator|HEMS Configurator]] -> settings -> output column -> select "EVSE RDX external" at desired position (1). Note that "EVSE inter." is reserved and can't be changed!
+  * [[wiki:20_rdc_charger:30_software:start#hems_configurator|HEMS Configurator]] -> settings -> output column -> select "EVSE RDX external" at desired position (1). Note that "EVSE inter." is reserved and can't be changed!
-{{wiki:rdx_charger:hems_config_cluster_02.png?direct&800|}}
+{{wiki:20_rdc_charger:hems_config_cluster_02.png?direct&800|}}
   * HEMS Configurator -> settings -> enter name and select icon (2). Message "Error - device is not responding" may appear as IP address is not defined yet.
-{{wiki:rdx_charger:hems_config_cluster_03.png?direct&800|}}
+{{wiki:20_rdc_charger:hems_config_cluster_03.png?direct&800|}}
   * HEMS Configurator -> limiter:
   * (3) enter allowed current value of grid fuses in case of connected grid power sensor, or max current limit of complete ev fleet if there is virtual grid active
   * (4) make sure to configure phase order for grid and RDX Chargers correct as dynamic load management may not work properly. **Double check!**
   * (5) select limiter priority for chargers: no limiter, limit last (last to be limited), limit second, limit first (first to be limited)
-{{wiki:rdx_charger:hems_config_cluster_04.png?direct&800|}}
+{{wiki:20_rdc_charger:hems_config_cluster_04.png?direct&800|}}
   * HEMS Configurator -> IO mux -> enter IP address of slave RDX Charger (6). Serial number (SN) will be listed automatically once connection is established.
-{{wiki:rdx_charger:hems_config_cluster_05.png?direct&800|}}
+{{wiki:20_rdc_charger:hems_config_cluster_05.png?direct&800|}}
   * HEMS Configurator -> ev fleet:\\ (7) master RDX Charger,\\ (8) connected slave RDX Charger with enabled control by master (green tick) and\\ (9) connected slave RDX Charger with disabled control (red X) -> master can not control it! To enable control, run RDX Charger app on slave charger and enable "EVSE works as slave".
-{{wiki:rdx_charger:hems_config_cluster_06.png?direct&800|}}\\
+{{wiki:20_rdc_charger:hems_config_cluster_06.png?direct&800|}}\\