Differences

This shows you the differences between two versions of the page.

--- wiki:20_rdc_charger:35_commissioning:03_wr_wm [2023/03/31 10:07] – ↷ Links adapted because of a move operation saso.santelj
+++ wiki:20_rdc_charger:35_commissioning:03_wr_wm [2023/08/02 13:47] (current) – saso.santelj
@@ Line 1: / Line 1: @@
 ====== Wireless modules WR-1 / WM-1 ======
-[[wiki:20_rdc_charger:03_hardware:23_wr-1|WR-1]] module is **W**ireless **R**elay.
+[[wiki:20_rdc_charger:15_hardware:23_wr-1|WR-1]] module is **W**ireless **R**elay.
-[[wiki:20_rdc_charger:03_hardware:22_wm-1|WM-1]] module is **W**ireless **M**odbus to modbus bridge.\\
+[[wiki:20_rdc_charger:15_hardware:22_wm-1|WM-1]] module is **W**ireless **M**odbus to modbus bridge.\\
-Check wiring possibilites at [[wiki:20_rdc_charger:05_wiring:start|wiring]] page.
+Check wiring possibilites at [[wiki:20_rdc_charger:25_wiring:start|wiring]] page.
-Bind a new module(s):
+Pair a new module(s):
-  * [[wiki:20_rdc_charger:06_software:start#settings|settings]] page -> **WM/WR binding**,
+  * [[wiki:20_rdc_charger:30_software:start#settings|settings]] page -> **WM/WR pairing**,
   * turn ON target module(s),
-  * within 10 seconds press **Bind module(s)**.
+  * within 10 seconds press **Pair module(s)**.
-{{wiki:rdx_charger:hems_wm_wr_settings.png?direct&400}}
+{{wiki:20_rdc_charger:hems_wm_wr_settings.png?direct&400}}
-Search for new devices after module(s) binding:
+Search for new devices after module(s) pairing:
-  * [[wiki:20_rdc_charger:06_software:start#settings|settings]] page -> **Scan w-less dev.**
+  * [[wiki:20_rdc_charger:30_software:start#settings|settings]] page -> **Scan w-less dev.**
-  * if [[wiki:20_rdc_charger:35_commissioning:01_power_sensor|power sensor]] is detected, message will appear on [[wiki:20_rdc_charger:06_software:start#settings|settings]] page under **new device** or next to source/consumer device (add it to required position - [[wiki:20_rdc_charger:35_commissioning:01_power_sensor|Power sensor adding]])
+  * if [[wiki:20_rdc_charger:35_commissioning:01_power_sensor|power sensor]] is detected, message will appear on [[wiki:20_rdc_charger:30_software:start#settings|settings]] page under **new device** or next to source/consumer device (add it to required position - [[wiki:20_rdc_charger:35_commissioning:01_power_sensor|Power sensor adding]])
-{{wiki:rdx_charger:hems_add_ps_02.png?direct&600}}
+{{wiki:20_rdc_charger:hems_add_ps_02.png?direct&600}}
-  * and/or when WR module is recognized by EVSE, it will be positioned on [[wiki:20_rdc_charger:06_software:start#io_mux|io mux]] page based on set address by jumper: WR-1 address 200 is assigned to WR 1 position, 201 -> WR 2, etc...
+  * and/or when WR module is recognized by EVSE, it will be positioned on [[wiki:20_rdc_charger:30_software:start#io_mux|io mux]] page based on set address by jumper: WR-1 address 200 is assigned to WR 1 position, 201 -> WR 2, etc...
-{{wiki:rdx_charger:hems_wm_wr_connected.png?direct&400}}
+{{wiki:20_rdc_charger:hems_wm_wr_connected.png?direct&400}}