Differences

This shows you the differences between two versions of the page.

--- wiki:20_rdc_charger:50_troubleshooting:start [2023/05/04 09:05] – alen.mejak
+++ wiki:20_rdc_charger:50_troubleshooting:start [2024/03/11 09:00] (current) – saso.santelj
@@ Line 1: / Line 1: @@
 ===== Troubleshooting =====
+<WRAP column 950px>
+RDC Charger recovers error automatically.
+To delete error by yourself long press button on charger housing or on application. **Charging is stopped while error is active.** **If red light still flashes, please read table bellow.**
-| **ERROR**        | **POSSIBLE CAUSES**           | **SOLUTION**                                       |
+|<100% 25% 35%>|
-|CP positive/negative voltage            |The voltage on the CP connector is out of permitted range| Check the charging cable and connector and reconnect the electric vehicle                                  |
+^ Error ^Possible causes ^ Possible solution ^
-|RCD sensor trip| Switch has detected a DC differential current               |If is problem with only one vehicle, please call an authorized vehicle service|
+|CP positive voltage\\ CP negative voltage |Measured voltage on CP pin is out of range. | Check your charging cable and plug. Reconnect your EV. If error still appears, please contact your EVSE service.  |
-|RCD sensor malfunction | RCD is damaged or not connected               |Please call  service of the charger                                                 |
+|RCD sensor trip                  | DC current leak detected. | Please try to connect another EV, if error still appears, please contact your EVSE service. Otherwise, please contact an authorized car service department. |
-|Undervoltage/Overvoltage          | The voltage at the input of the charger is out of permitted range           | Please call  service of the charger                                                |
+|RCD sensor malfunction           | RCD sensor is damaged or not connected. | Please contact your EVSE service. |
-|Charge with ventilation|The vehicle requires charging with ventilation and “Charging with ventilation” is not enabled on the user interface  |Enable "Charging with ventilation" on the user interface if the electric vehicle is charged  in a ventilated area or outdoor                              |
+|Undervoltage\\ Overvoltage       | Supply voltage is out of range.  | Please contact your EVSE installer. |
-|PS reading error|There is no connection to the power sensor in the charger housing|Please call  service of the charger|
+|Charge with ventilation          | EV requests charging with ventilation and "Charging with ventilation" is not enabled on configurator. | Enable "Allow charging with ventilation" if charged EV is located in ventilated area. |
-|Current is higher than allowed|The vehicle is charged with higer current that is allowed|Try charging another electric vehicle and if the error is still present, please call the charger service. Otherwise, call authorized  service of your vehicle                                          |
+|PS reading error (EVSE)          | No communication with internal power sensor. | Please contact your EVSE service. |
-|Power          |Excessive temperature inside the housing of the charger|Check that RDC charger is not directly exposed to the sun light. Please call the charger installer|
+|PS reading error (grid)          | No communication with grid power sensor. \\ DLM can not work properly. | Check connection with grid power sensor. Please contact your EVSE installer. |
-|Internal temperature too high| Battery           | Optional                                             |
+|Current is higher than allowed   | Vehicle draws more current/power than allowed. |Please try to charge another EV, if error still appears, please contact your EVSE service. Otherwise, please contact an authorized car service department.|
+|Internal temperature is too high | Temperature inside of charger is too high. | Make sure charger is not exposed to direct sunlight. Please contact your EVSE installer. |
+|Can not lock                     | Only for charger with socket: Socket can not lock the connected plug. | Unplug the cable and check if the plug is clean. If it's clean, try charging with a different cable. If it still doesn't work, contact the EVSE installer. |
+|Can not unlock                   | Only for charger with socket: Socket can not unlock the connected plug. | Unplug the cable on the vehicle side and try again. If it doesn't work, contact the EVSE installer. |
+|Socket temperature is too high   | Only for charger with socket: The socket is overheating, socket pin temperature is too high. | Try different solutions:  \\ 1. Unplug the cable and check if the plug is clean. \\ 2. Turn off the power supply to the charger and check if the socket is clean. \\ 3. Try charging with a different cable. \\ If it doesn't work, contact the EVSE installer. |
+|Unavailable                      | Parent system has set the charging station to "unavailable" status; Usually for system maintenance or upgrades. | Wait for the upgrades to complete. If it takes more than 5 minutes, contact EVSE service or your parent system provider for information. |
+|Other error                      | Other errors that can not be resolved by the user. | Contact EVSE service. |
+</WRAP>