Differences

This shows you the differences between two versions of the page.

--- wiki:20_rdc_charger:35_commissioning:04_heat_pump [2023/03/31 10:07] – ↷ Page moved from wiki:20_rdc_charger:07_commissioning:04_heat_pump to wiki:20_rdc_charger:35_commissioning:04_heat_pump saso.santelj
+++ wiki:20_rdc_charger:35_commissioning:04_heat_pump [2025/03/21 13:19] (current) – saso.santelj
@@ Line 1: / Line 1: @@
 ====== Heat pump ======
-RDX charger supports monitoring and control of heat pump.
+RDC charger supports monitoring and control of heat pump.
 Monitoring consists of tracking power and electricity consumption in real time as well as storing measured data on cloud service.
@@ Line 7: / Line 7: @@
 Control depends on heat pump model if it supports control by an external device.
-**Note**: Max 4 heat pumps are supported by RDX Charger.
+**Note**: Max 4 heat pumps are supported by RDC Charger.
 Add a heat pump device by configurator:
-  * [[wiki:20_rdc_charger:06_software:start#settings|settings page]] -> column 'output' -> select heat pump 1..4,
+  * [[wiki:20_rdc_charger:30_software:start#settings|settings page]] -> column 'output' -> select heat pump 1..4,
-  * connect power sensor or define [[wiki:20_rdc_charger:06_software:start#settings|P nominal]],
+  * connect power sensor or define [[wiki:20_rdc_charger:30_software:start#settings|P nominal]],
   * enter name and select icon.
-{{wiki:rdx_charger:heat_pump_settings_01.png?direct&600}}
+{{wiki:20_rdc_charger:heat_pump_settings_01.png?direct&600}}
 Define control for heat pump:          :!: check for heat pump control capabilities\\
-  * [[wiki:20_rdc_charger:06_software:start#io mux|io mux page]] -> Heat pump control mode -> select control modes,
+  * [[wiki:20_rdc_charger:30_software:start#io mux|io mux page]] -> Heat pump control mode -> select control modes,
 **Examples of settings for heat pump:**\\ HP has 3 control channels (supports off, reduced power and increased power), then select as is for **Heat pump 4**,\\
@@ Line 24: / Line 24: @@
 <WRAP column 400px>
-{{wiki:rdx_charger:heat_pump_settings_02.png?direct&500}}
+{{wiki:20_rdc_charger:heat_pump_settings_02.png?direct&500}}
 </WRAP>
 <WRAP column 400px>
-{{wiki:rdx_charger:heat_pump_settings_05.png?direct&200}}\\
+{{wiki:20_rdc_charger:heat_pump_settings_05.png?direct&200}}\\
 </WRAP>
 <WRAP clear></WRAP>
 Define WR-1 output function:
-  * [[wiki:20_rdc_charger:06_software:start#io mux|io mux page]] -> wireless relay WR-1 output function -> select HP channels,
+  * [[wiki:20_rdc_charger:30_software:start#io mux|io mux page]] -> wireless relay WR-1 output function -> select HP channels,
   * to each WR module wired to heat pump,
-{{wiki:rdx_charger:heat_pump_settings_03.png?direct&600}}\\
+{{wiki:20_rdc_charger:heat_pump_settings_03.png?direct&600}}\\
 Change heat pump control state:
-  * [[wiki:20_rdc_charger:06_software:start#home|home page]] -> press consumer HP icon
+  * [[wiki:20_rdc_charger:30_software:start#home|home page]] -> press consumer HP icon
-{{wiki:rdx_charger:heat_pump_settings_04.png?direct&600}}\\
+{{wiki:20_rdc_charger:heat_pump_settings_04.png?direct&600}}\\
 :!: Possible states are those defined in Heat pump control modes
 <WRAP column 600px>
 ^ Heat pump output state ||
-|  {{wiki:rdx_charger:sgrhp_off.png?direct&20|}}         | Off |
+|  {{wiki:20_rdc_charger:sgrhp_off.png?direct&20|}}         | Off |
-|  {{wiki:rdx_charger:sgrhp_down.png?direct&20|}}        | Reduced |
+|  {{wiki:20_rdc_charger:sgrhp_down.png?direct&20|}}        | Reduced |
-|  {{wiki:rdx_charger:sgrhp_normal.png?direct&20|}}      | Normal |
+|  {{wiki:20_rdc_charger:sgrhp_normal.png?direct&20|}}      | Normal |
-|  {{wiki:rdx_charger:sgrhp_up.png?direct&20|}}          | Increased  |
+|  {{wiki:20_rdc_charger:sgrhp_up.png?direct&20|}}          | Increased  |
-|  {{wiki:rdx_charger:sgrhp_full_power.png?direct&20|}}  | Increased + additional el.heater |
+|  {{wiki:20_rdc_charger:sgrhp_full_power.png?direct&20|}}  | Increased + additional el.heater |
 </WRAP>