Differences

This shows you the differences between two versions of the page.

--- wiki:20_rdc_charger:35_commissioning:01_power_sensor [2023/03/31 10:07] – ↷ Links adapted because of a move operation saso.santelj
+++ wiki:20_rdc_charger:35_commissioning:01_power_sensor [2025/06/11 12:08] (current) – saso.santelj
@@ Line 1: / Line 1: @@
 ====== Power sensor adding ======
-{{wiki:rdx_charger:hems_add_ps.png?direct&600}}\\
+{{wiki:20_rdc_charger:hems_add_ps.png?direct&600}}\\
 :!: Adding is supported one by one\\
-:!: Before adding or removing power sensor via wireless [[wiki:20_rdc_charger:15_hardware:22_wm-1|WM-1]] module, button [[wiki:20_rdc_charger:06_software:start#settings|Settings page]] -> **Scan w-less dev.** must be active!\\
+:!: Before adding or removing power sensor via wireless [[wiki:20_rdc_charger:15_hardware:22_wm-1|WM-1]] module, button [[wiki:20_rdc_charger:30_software:start#settings|Settings page]] -> **Scan w-less dev.** must be active!\\
   *   Connect communication bus (to only one power sensor)
   *   Only for PM1-E-D: Press and hold the push-button on the power sensor until it appears **-SEt-** on display
-  *   In [[wiki:20_rdc_charger:06_software:start#settings|HEMS Configurator]] power sensor should appear as a **new device**
+  *   In [[wiki:20_rdc_charger:30_software:start#settings|HEMS Configurator]] power sensor should appear as a **new device**
   *   Click on the **add** button next to the source or consumer to which sensor is measuring
   *   Connect communication bus to the next power sensor and repeat procedure
@@ Line 18: / Line 18: @@
 <WRAP column 350px>
 ^ Address ^ Power sensor position|
-| 149 | Default (new PS) appears in field **new device**  |
+| 1, 149 | Default (new PS) appears in field **new device**  |
 | 150 | Grid  |
 | 154,155,156 | Power plants  |
@@ Line 27: / Line 27: @@
 <WRAP column 450px>
-{{wiki:rdx_charger:ps_position.png?direct&300|}}
+{{wiki:20_rdc_charger:ps_position.png?direct&300|}}
 </WRAP>
@@ Line 33: / Line 33: @@
 ==== Power sensor removing ====
-{{wiki:rdx_charger:hems_del_ps.png?direct&600}}
+{{wiki:20_rdc_charger:hems_del_ps.png?direct&600}}
   * Make sure the **new device** is empty (as on image above)
   * Only for PM1-E-D: Press the button on power sensor until **-Set-** appears on the display
-  * In [[wiki:20_rdc_charger:06_software:start#settings|HEMS Configurator]] press **del** button next to the sensor
+  * In [[wiki:20_rdc_charger:30_software:start#settings|HEMS Configurator]] press **del** button next to the sensor
   * After a few seconds, the sensor should appear as a **new device**
   * The sensor can be removed or it can be assigned to another device
@@ Line 43: / Line 43: @@
 ==== Without grid power sensor ====
-  *   [[wiki:20_rdc_charger:06_software:start#settings|Settings]] -> **Virtual grid PS** is an option if no grid meter is used. Power, current and energy will be calculated from other power sensors.
+  *   [[wiki:20_rdc_charger:30_software:start#settings|Settings]] -> **Virtual grid PS** is an option if no grid meter is used. Power, current and energy will be calculated from other power sensors.