https://wiki.robotina.com/ 2026-04-20T02:44:35+00:00 https://wiki.robotina.com/ https://wiki.robotina.com/lib/exe/fetch.php?media=wiki:logo.png text/html 2025-06-11T12:08:59+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:01_power_sensor&rev=1749643739&do=diff Power sensor adding :!: Adding is supported one by one :!: Before adding or removing power sensor via wireless WM-1 module, button Settings page -> Scan w-less dev. must be active! * Connect communication bus (to only one power sensor) * Only for PM1-E-D: Press and hold the push-button on the power sensor until it appears text/html 2023-05-26T13:04:56+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:02_power_plant&rev=1685106296&do=diff Power plant connection The power plants can be connected to the grid in two ways: serial with grid power sensor parallel with grid power sensor When configuring the power plant, select * in: serial (internal) with grid power sensor * text/html 2023-08-02T13:47:19+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:03_wr_wm&rev=1690984039&do=diff Wireless modules WR-1 / WM-1 WR-1 module is Wireless Relay. WM-1 module is Wireless Modbus to modbus bridge. Check wiring possibilites at wiring page. Pair a new module(s): * settings page -> WM/WR pairing, * turn ON target module(s), * within 10 seconds press Pair module(s) text/html 2025-03-21T13:19:10+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:04_heat_pump&rev=1742563150&do=diff Heat pump RDC charger supports monitoring and control of heat pump. Monitoring consists of tracking power and electricity consumption in real time as well as storing measured data on cloud service. Control depends on heat pump model if it supports control by an external device. text/html 2024-08-26T15:07:55+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:05_dlm&rev=1724684875&do=diff Dynamic Load Management RDC Charger supports power consumption (current draw) control to prevent circuit breaker tripping (overloading). Overloading causes multiple high-energy appliances working at the same time, such as an oven, dishwasher, heat pump and EV charging. text/html 2025-03-21T13:07:58+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:06_ev_fleet&rev=1742562478&do=diff EV fleet RDC charger supports connection of up to 8 RDC Chargers - EV fleet. In such configuration only one RDC Charger (master) is in charge of other connected chargers (slave). Master RDC Charger monitors: * current draw by other slave chargers and in real time allocates (limits) available capacity allowing them to charge without overloading, text/html 2023-05-26T13:04:56+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.robotina.com/doku.php?id=wiki:20_rdc_charger:35_commissioning:start&rev=1685106296&do=diff Commissioning when the charger is mounted (on wall or freestanding set) , properly connected, we can continue with the commissioning. Strictly follow Safety instructions! :!: Once RDC Charger is configured, it does not require further connection to internet or configurator for normal operation !